resealing a slide topper and the roof before the snow flies, what sealant and how often
Mile 07Opened by slide_seal_redoNov 5, 2025in Fifth-wheel talk6 posts
slide_seal_redoOPSnowbird#1
Missoula, MT31 posts · joined Nov 2025Heartland Bighorn 3575EL · Ford F-350
2016 Bighorn 3575EL, four slides, so i have a lot of roof and a lot of seams to worry about. i got up there sunday with a putty knife and a flashlight before the first real snow because montana does not mess around in november, and i want to do this right the first time.
what i found on the lap seams around the front cap and the two bathroom vents was the old self-leveling sealant cracked and pulling away from the fiberglass at the edges, little hairline channels you could slide a business card into. nothing leaking inside yet that i can find, no soft spots in the ceiling, but i do not want to find out in february with a foot of snow sitting up there melting into a seam.
two questions. one, do i scrape all the old stuff off and start over, or do i just lay fresh self-leveling over the top of the old cracked bead. two, the slide topper fabric over the big living room slide has a sun-faded stripe and the stitching at the roller end is going. is that something i replace now or something i baby through one more winter.
roof is EPDM, or at least that is what the previous owner wrote in the binder. 2016 Heartland if that tells anybody what membrane it left the factory with.
Glenn P.Moderator#2
Sierra Vista, AZ16 posts · joined Nov 2025Solitude 310GK · Ram 3500 dually · B&W Companion
do not lay fresh over cracked. it traps water under the new bead and you will be back up there in a year chasing the same leak from a worse starting point.
here is how i do a seam that is cracked but not leaking, which is exactly where yours is and is the good time to catch it. get a plastic scraper and a heat gun on low, warm the old self-leveling until it goes soft and lift the loose, failed stuff off. you are not trying to get down to bare fiberglass like a body shop, you are removing anything that is lifting or cracked. wipe the seam with denatured alcohol, let it flash off, then lay a fresh bead of self-leveling lap sealant down the horizontal seams and let it find its own level. the vertical joints on the end caps want the non-sag version so it does not run.
on an EPDM roof use a sealant rated for EPDM, and the self-leveling kind is designed to go on the horizontal seams and flow out flat. the manufacturer spells out which product goes on which membrane right on their site at dicorproducts.com, and it matters, because a TPO-only sealant on an EPDM roof is how people create the leak they were trying to prevent.
get up there twice a year and look, spring and fall. five minutes with a flashlight beats a ceiling job every time.
fulltime_since_juneFull-timer#3
Sioux Falls, SD64 posts · joined Nov 2025Cedar Creek 34RL2 · Chevy Silverado 3500
on the slide topper, replace it now and do not baby it. i babied one exactly like you are describing, faded with the end stitching going, through one more winter on my Cedar Creek, and in march the fabric let go at the roller in a wind gust and wrapped itself around the awning arm. the replacement fabric was about 140 dollars for my size, the shop wanted 400 to install it, and i did it in my own site in an afternoon with my neighbor holding the roller and winding the torsion spring while i fed the new fabric into the channel.
the part people skip: measure the old one on the rig, roller tube length and the fabric width, do not trust the floorplan brochure number. mine was two inches off what the chart said because the factory used whatever was in the rack that week.
one winter tip from up here. the slide toppers hold snow and then the snow freezes and the weight pulls the fabric down into the slide. if you leave the rig parked with slides out in snow country, get a broom on a pole and knock the snow off the toppers, or bring the slides in when a big storm is coming.
desert_snowbirdSnowbird#4
Yuma, AZ28 posts · joined Nov 2025Reflection 297RSTS · Ram 3500
different climate problem, same material. down here the roof does not freeze, the sun cooks it. the self-leveling on my Reflection was chalking and getting brittle at year three just from the Yuma sun, no snow involved. so the twice a year look that Glenn said holds whether you are freezing or baking, the failure just looks different.
one thing i will add for the dry heat crowd. a 303 type UV protectant on the slide topper fabric and the seals a couple times a season actually buys you time out here. it does nothing structural but the fabric and the rubber last noticeably longer when they are not getting bleached dry. not a fix, just a stall.
slide_seal_redoOPSnowbird#5
Missoula, MT31 posts · joined Nov 2025Heartland Bighorn 3575EL · Ford F-350
did it over two dry days last week before the storm that is sitting on us now. heat gun on low to lift the cracked self-leveling, plastic scraper, denatured alcohol wipe, then fresh self-leveling on the horizontals and non-sag around the front cap verticals like Glenn said. four tubes of self-leveling and one of non-sag, about 55 dollars in sealant, and most of a saturday on my knees on a cold roof.
the thing i did not expect: once the old failed bead was off, two of the seams had the putty tape under them showing daylight at one spot each, so i caught that right at the point where it was about to become an inside problem. fulltime_since_june was right about the topper too, i pulled the living room one and the fabric tore like paper when i flexed it, there was no winter left in it. new fabric is ordered.
knocked the first snow off the other three toppers with a broom this morning. so that is the new chore.
andersen_hitch_userWeekender#6
Green Bay, WI19 posts · joined Nov 2025Forest River Sandpiper 321RL · Ford F-250 short bed
reading this three weeks late and glad i did. went up on my Sandpiper saturday expecting nothing and found the sealant around the refrigerator vent cap cracked exactly like the OP described. caught it before it leaked into the slide roof.
for anybody in the frozen part of the country reading this in january and panicking: you cannot do a proper self-leveling job in the cold, the sealant will not flow or cure right much below 50 degrees. if you find a cracked seam now and it is already freezing, a strip of the eternabond style roof tape over the seam is a legitimate get-you-to-spring fix, and then you do it properly when it warms up. do not try to lay self-leveling on a 20 degree roof and call it done.
Log in to reply. No account yet? Ask a mod, it takes a day or two.